富美家室內門安裝維護攻略

Installation and Maintenance Guide for Fumijia Indoor Doors

一、安裝篇：科學施工確保十年品質

1、 Installation article: Scientific construction ensures ten-year quality

1. 安裝前的核心準備

1. Core preparation before installation

環境檢測：使用溫濕度計（如得力 8809）檢測安裝環境，要求濕度≤75%、溫度 15-25℃。若濕度超標，需提前 3 天開啟除濕機（推薦格力 DH20EH）。

Environmental detection: Use a temperature and humidity meter (such as Deli 8809) to detect the installation environment, requiring humidity ≤ 75% and temperature 15-25 ℃. If the humidity exceeds the standard, the dehumidifier (recommended Gree DH20EH) should be turned on 3 days in advance.

材料驗收：

Material acceptance:

門扇對角線誤差≤1.5mm（用 5m 卷尺測量）

Diagonal error of door leaf ≤ 1.5mm (measured with a 5m tape measure)

表面平整度：2m 靠尺檢測誤差≤0.5mm

Surface flatness: 2m ruler detection error ≤ 0.5mm

封邊完整性：熱彎封邊門圓弧處需無縫隙，鋁封邊門氧化層無破損

Edge integrity: There should be no gaps at the arc of the hot bending edge sealing door, and the oxide layer of the aluminum edge sealing door should not be damaged

2. 門套安裝的關鍵工藝

2. Key processes for installing door frames

膨脹螺栓固定：采用 M6×60mm 不銹鋼膨脹螺栓，間距≤500mm，門框垂直度誤差≤2mm（用激光水平儀校準）。

Expansion bolt fixation: M6 × 60mm stainless steel expansion bolts are used with a spacing of ≤ 500mm, and the verticality error of the door frame is ≤ 2mm (calibrated with a laser level).

發泡膠填充：聚氨酯發泡膠（如東洋膠業）填充厚度 15-20mm，固化后切除多余部分，避免擠壓門扇。

Foam filling: Polyurethane foam (such as Toyo Rubber) is filled with a thickness of 15-20mm, and excess parts are cut off after curing to avoid squeezing the door leaf.

密封條安裝：三元乙丙膠條（硬度 50 Shore A）需預留 3-5mm 伸縮量，用 3M 雙面膠固定，避免出現漏光縫隙。

Sealing strip installation: EPDM rubber strip (hardness 50 Shore A) needs to reserve 3-5mm expansion and contraction, and be fixed with 3M double-sided tape to avoid light leakage gaps.

3. 門扇安裝的技術要點

3. Technical points for door leaf installation

合頁開槽：使用 3mm 木工鑿精準開槽，深度與合頁厚度一致（推薦史丹利 55-020）。

Joint slotting: Use a 3mm woodworking chisel to accurately slot, with a depth consistent with the thickness of the joint (recommended Stanley 55-020).

門縫控制：

Door gap control:

上縫 2-3mm，側縫 2-2.5mm，下縫 6-8mm（用塞尺測量）

Upper seam 2-3mm, side seam 2-2.5mm, lower seam 6-8mm (measured with a feeler gauge)

熱彎封邊門需預留 0.5mm 熱脹冷縮間隙

The hot bending edge sealing door needs to reserve a 0.5mm gap for thermal expansion and contraction

五金件安裝：

Hardware installation:

鎖體開孔：專用 35mm 開孔器（如博世 PBM 35）

Lock body opening: specialized 35mm hole opener (such as Bosch PBM 35)

地吸安裝：吸力≥50N，距門扇底部 150mm

Ground suction installation: suction force ≥ 50N, 150mm from the bottom of the door leaf

4. 特殊結構處理

4. Special structural treatment

熱彎封邊門：封邊溫度 180-220℃，壓力 8-12MPa，切割后需用同色 ABS 封邊條二次封邊。

Hot bending edge sealing door: The sealing temperature is 180-220 ℃, and the pressure is 8-12MPa. After cutting, ABS edge sealing strips of the same color are required for secondary sealing.

鋁封邊門：環氧樹脂膠（如 3M DP460）粘合，固化時間≥24 小時，安裝時覆蓋 3M 保護膜防劃傷。

Aluminum sealed edge door: bonded with epoxy resin adhesive (such as 3M DP460), curing time ≥ 24 hours, covered with 3M protective film to prevent scratches during installation.

二、維護篇：全周期保養方案

2、 Maintenance section: Full cycle maintenance plan

1. 日常清潔規范

1. Daily cleaning standards

表面護理：

Surface care:

污漬處理：中性清潔劑（pH 值 7-8）+ 超細纖維布（如 3M 思高）

Stain treatment: Neutral cleaner (pH 7-8)+ultra-fine fiber cloth (such as 3M Sigao)

劃痕修復：輕微劃痕用牙膏研磨，深度劃痕用同色修補膏（如富美家原廠修補套裝）

Scratch repair: For minor scratches, grind them with toothpaste, and for deep scratches, use the same color repair paste (such as the original Fumeijia repair kit)

五金件保養：

Hardware maintenance:

合頁、鎖舌：每月滴加鋰基潤滑脂（如克魯勃 GEM4）

Folds and tongue locks: Add lithium based grease (such as Krupp GEM4) every month

拉手：定期檢查螺絲扭矩（2-3N?m）

Handle: Regularly check the screw torque (2-3N? M)

2. 周期性維護計劃

2. Periodic maintenance plan

年度保養：

Annual maintenance:

更換密封條（建議使用富美家原廠配件）

Replace the sealing strip (it is recommended to use original accessories from Fumijia)

檢查門扇底部防塵條，磨損超 2mm 需更換

Check the dust strip at the bottom of the door leaf. If it is worn beyond 2mm, it needs to be replaced

防火性能檢測：

Fire performance testing:

每 2 年委托第三方檢測耐火時間（A 級≥1.5 小時）

Entrust a third-party to test the fire resistance time every 2 years (Grade A ≥ 1.5 hours)

避免粘貼易燃裝飾物

Avoid pasting flammable decorations

3. 特殊場景應對

3. Response to special scenarios

高濕度環境：

High humidity environment:

衛生間門：每月用除濕機控制濕度≤60%，底部加裝防潮鋁型材

Toilet door: Use a dehumidifier to control humidity ≤ 60% every month, and install moisture-proof aluminum profiles at the bottom

廚房門：使用不銹鋼清潔劑（pH4-6）去除油漬

Kitchen door: Use stainless steel cleaner (pH 4-6) to remove oil stains

醫療場所：

Medical facilities:

每周用含銀離子清潔劑（濃度 0.01-0.05%）擦拭，維持抗菌率≥99%

Wipe with silver ion cleaner (concentration 0.01-0.05%) every week to maintain an antibacterial rate of ≥ 99%

每季度紫外線消毒 30 分鐘

UV disinfection for 30 minutes every quarter

本文由富美家室內門友情奉獻.更多有關的知識請點擊:http://aa741.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is a friendly contribution from Fumijia Interior Door For more information, please click: http://aa741.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message